Fichier produit



PRESTIGE DM FDH+R12 FDH L1 PRISMATIC MR – mounting rail The mounting rail is manufactured by calandering of 0,6 mm sheet steel, surface coated with white polyester resin paint. Rail is available in 2 lenghts (double-body and triplebody) for lamps FD or FDH. It is available to order single-body mounting rail on request. The wiring of 5x1,5mm2 or 7x1,5mm2 cross-section can be installed in the profile. It is possible to order wiring with 2,5 mm2 cross-section on request. Ends of conductors installed in the mounting rail are ended with the axial connector, which allows conductive continuous connection of the mounting rails without any tools. The connectors, that are part of wiring, allow simple clamping of luminaire bodies to the mounting rails. Pre-wired trunking Wiring for the Prestige system is fi tted at the factory and prepared for a rapid electrical installation. Trunking systems with built-in conductors provides big fl exibility. Prestige system have electrical connection points for mains, lighting control and emergency lighting supply at pre-defi ned points – in distances for FD 58W or FDH 35/49/80W fluorescent lamp. For simple to complex confi gurations, the mounting rails feature three, five or seven-conductor wiring with 1,5 mm2 cross-section. Cross-section 2,5 mm2 is available on request. If emergency lighting is rerquired in the lighting installation, some of lighting fixtures has to be equipped with emegency unit, which needs extra conductor for battery supply. DEVICE MOUNT FDH Device mount for FDH fluorescent lamps is normally installed by using of a mounting rail. Device mount is manufactured by calandering of sheet steel, surface coated with white polyester resin paint. Device mount is available in single and twin lamp version, where both versions can use mostly the same optic. Device mount is equipped with 2 clamping mechanisms which allow simple gripping of the device mount to the mounting rail. By using of these clamping mechanisms it is also possible to fi x refl ectors to the device mount without any tools. The connector placed on the gear tray is used for simple electrical connection of the lighting fixture to the mounting rail. This connector also allows simple selection of the phase in three-phase system (5 or 7-pole electrical connection). Phase selection is made by repositioning of movable contact into the required position. Additional free contatcts allow configuration of a standard lighting fixture into an emergency luminaire or into a dimmable luminaire. DM FDH can be equipped with an electronic ballast or with a dimmable electronic balast (analogue or digital). Emergency version is available on request. In case of missing device mount DM, arose empty gap in mounting rail can be covered with DM cover. It is required to make a separate order for lamps. R12 FDH L1 Reflector accessory made of 0,6 mm steel sheet; fi nished with white powder coatingRAL. Designed for one or twin fluorescent lamps FDH. Light distribution direct, wide angle. Ideal for installations which require high illumination levels and low energy consumption. PRISMATIC FDH R12 Decorative closed prismatic optic for a wider beam spread. Suitable for low installation rooms and when mechanical protection of lamps is requested. Prismatic structure plate made of PMMA is for fitting in reflector R12 FDH L1 and R12 FDH L2. Accessory available for one or two FDH lamps. 

Ampoules disponibles Puissance nominative du lampe Flux lumineux de la source Efficacité lumineuse CCT CRI
1 x Lampe flourescente linéaire T16 49 W 4300 lm 61 lm/W 4000 K 85


Surface lumineux 1 

1 x Lampe flourescente linéaire T16 

Type de montage 

Suspendu, Contact rail

Forme et dimensions 

Longueur: 1485 mm

Largeur: 113 mm

Hauteur: 121 mm




Puissance du système: 52 W

Types de protection 

IP: 20

Fichier Photométrique

ZIP file