Fichier produit

PRESTIGE DM FDH+R12 FDH AL ASYMMETRIC 1x80W

OMS

PRESTIGE DM FDH+R12 FDH AL ASYMMETRIC MR – mounting rail The mounting rail is manufactured by calandering of 0,6 mm sheet steel, surface coated with white polyester resin paint. Rail is available in 2 lenghts (double-body and triplebody) for lamps FD or FDH. It is available to order single-body mounting rail on request. The wiring of 5x1,5mm2 or 7x1,5mm2 cross-section can be installed in the profi le. It is possible to order wiring with 2,5 mm2 cross-section on request. Ends of conductors installed in the mounting rail are ended with the axial connector, which allows conductive continuous connection of the mounting rails without any tools. The connectors, that are part of wiring, allow simple clamping of luminaire bodies to the mounting rails. Pre-wired trunking Wiring for the Prestige system is fi tted at the factory and prepared for a rapid electrical installation. Trunking systems with built-in conductors provides big fl exibility. Prestige system have electrical connection points for mains, lighting control and emergency lighting supply at pre-defi ned points – in distances for FD 58W or FDH 35/49/80W fl uorescent lamp. For simple to complex confi gurations, the mounting rails feature three, fi ve or seven-conductor wiring with 1,5 mm2 cross-section. Cross-section 2,5 mm2 is available on request. If emergency lighting is rerquired in the lighting installation, some of lighting fi xtures has to be equipped with emegency unit, which needs extra conductor for battery supply. DEVICE MOUNT FDH Device mount for FDH fl uorescent lamps is normally installed by using of a mounting rail. Device mount is manufactured by calandering of sheet steel, surface coated with white polyester resin paint. Device mount is available in single and twin lamp version, where both versions can use mostly the same optic. Device mount is equipped with 2 clamping mechanisms which allow simple gripping of the device mount to the mounting rail. By using of these clamping mechanisms it is also possible to fi x refl ectors to the device mount without any tools. The connector placed on the gear tray is used for simple electrical connection of the lighting fi xture to the mounting rail. This connector also allows simple selection of the phase in three-phase system (5 or 7-pole electrical connection). Phase selection is made by repositioning of movable contact into the required position. Additional free contatcts allow confi guration of a standard lighting fi xture into an emergency luminaire or into a dimmable luminaire. DM FDH can be equipped with an electronic ballast or with a dimmable electronic ballast (analogue or digital). Emergency version is available on request. In case of missing device mount DM, arose empty gap in mounting rail can be covered with DM cover. It is required to make a separate order for lamps. R12 FDH AL ASYMMETRIC Asymmetrical light distribution that enables designers to accentuate walls and displays while still applying the same type of luminaire appearance as used for general lighting. Reflector is designed for FDH fl uorescent lamps - both single or twin lamp versions. Suitable for mounting halls, production sites, workshops and especially for wall, blackboard and shelf lighting. 

Ampoules disponibles Puissance nominative du lampe Flux lumineux de la source Efficacité lumineuse CCT CRI
1 x Lampe flourescente linéaire T16 80 W 6150 lm 66 lm/W 4000 K 85
PRESTIGE DM FDH+R12 FDH AL ASYMMETRIC 1x80W

PRESTIGE DM FDH+R12 FDH AL ASYMMETRIC 1x80W 

Surface lumineux 1 

1 x Lampe flourescente linéaire T16 

Type de montage 

Suspendu, Contact rail

Forme et dimensions 

Longueur: 1485 mm

Largeur: 199 mm

Hauteur: 208 mm

Réglable 

Rigide

Électrique 

Puissance du système: 83 W

Types de protection 

IP: 20

Fichier Photométrique

ZIP file